4-20 mA & Serial Data Output Transmitter for DC Voltage or Current

Laureate DC input transmitters provides six voltage input ranges and four current input ranges, all factory calibrated and jumper selectable. The 200.00 mV and 2.0000 V ranges provide a high input impedance of 1 GΩ to minimize the load on the voltage signal. A 5.000A range measures the IR drop across a built-in 10 mΩ current shunt. The transmitters can be scaled in software for use with external shunts.

Fast read rate at up to 50 or 60 conversions per second while integrating the signal over a full power line cycle is ideal for peak or valley capture and for real-time computer interface and control.

Digital signal filtering modes are selectable for stable readings in electrically noisy environments.

An unfiltered selection provides true peak and valley readings and aids in control applications.
A batch average filter selection averages each 16 conversions for an update every 1/4 sec.
An adaptive moving average filter selection provides a choice of 8 time constants from 80 ms to 9.6 s. When a significant change in signal level occurs, the filter adapts by briefly switching to the shortest time to follow the change, then reverts back to its selected time constant. An Auto setting selects the time constant selection based on signal noise.

Standard features of Laureate LT transmitters include:

4-20 mA, 0-10V or -10V to +10V analog transmitter output, isolated, jumper-selectable and user scalable. All selections provide 16-bit (0.0015%) resolution of output span and 0.02% output accuracy of a reading from -99,999 to +99,999 counts that is also transmitted digitally. Output isolation from signal and power grounds eliminates potential ground loop problems.
Serial communications output, RS232 or RS485 (half or full duplex), jumper selectable. Three protocols are user selectable: Modbus RTU, Modbus ASCII, or Laurel ASCII. Modbus operation is fully compliant with Modbus Over Serial Line Specification V1.0 (2002). The Laurel ASCII protocol is simpler than the Modbus protocol and is recommended when all devices are Laureates.
Dual solid state relays, isolated, for alarm or control. Rated 120 mA at 130 Vac or 170 Vdc.
Transducer excitation output, isolated. User selectable 5V@100 mA, 10V@120 mA or 24V@50 mA.
Universal 85-264 Vac power. Low-voltage 10-48 Vdc or 12-32 Vac power is optional.

Easy Transmitter programming is via Laurel's Instrument Setup Software, which runs on a PC under MS Windows. This software can be downloaded from this website at no charge. The required transmitter-to-PC interface cable is available from Laurel (P/N CBL04).

Specifications

Laureate 4-20 mA and RS2332/RS485 Transmitter for DC Voltage or Current Input

Analog Input	Range	Resolution	Accuracy	Input Ohms
DC Voltage	±200.00 mV	10 µV	0.01% FS ± 2 cts	1 GΩ
	±2.0000 V	100 µV	0.01% FS ± 2 cts	1 GΩ
	±20.000 V	1 mV	0.01% FS ± 2 cts	10 MΩ
	±200.00 V	10 mV	0.01% FS ± 2 cts	10 MΩ
	±600.0 V*	100 mV	± 0.4 V	10 MΩ
DC Current	±2.0000 mA	0.1 µA	0.01% FS ± 2 cts	100 Ω
	±20.000 mA	1 µA	0.01% FS ± 2 cts	10 Ω
	±200.00 mA	10 µA	0.01% FS ± 2 cts	1 Ω
	±5.000 A	1 mA	±10 mA	0.01 Ω
* Range ETL certified to ±300.0 V
Input Resolution	16 bits (65,536 steps)
Update Rate, Max	50/sec at 50 Hz, 60/sec at 60 Hz
Max applied voltage	600 Vac for 20, 200 & 600 V ranges, 125 Vac other ranges
Over-current protection	25x for 2 mA, 8x for 20 mA, 2.5x for 200 mA, 1x for 5 A
Analog Output (standard)
Output Levels	4-20 mA, 0-20 mA, 0-10 Vdc, -10 to +10Vdc (user selectable)
Compliance, 4-20 mA	10V (0-500Ω load)
Compliance, 0-10V	2 mA (5 kΩ load)
Output Resolution	16 bits (65,536 steps)
Output Accuracy	0.02% of output span plus conversion accuracy
Output Isolation	250V rms working, 2.3 kV rms per 1 minute test
Serial Data Output (standard)
Signal Types	RS232 or RS485 (half or full duplex), jumper selectable
Data Rates	300, 600, 1200, 2400, 4800, 9600, 19200 baud
Output Isolation	250V rms working, 2.3 kV rms per 1 min test
Serial Protocols	Modbus RTU, Modbus ASCII, Laurel ASCII
Modbus Compliance	Modbus over Serial Line Specification V1.0 (2002)
Ethernet Connector	RJ45 jack for 10/100 Base-T Ethernet cable
RS232/485 Connector	Screw terminals for easy daisy chaining
Digital Addresses	247 for Modbus, 31 for Laurel ASCII
Dual Relay Output (standard)
Relay Type	Two solid state relays, SPST, normally open, Form A
Load Rating	120 mA at 140 Vac or 180 Vdc
Transducer Excitation Output (standard)
Output Levels	5V@100 mA, 10V@120 mA, 24V@50 mA (jumper selectable)
Output Isolation	50V from signal ground
Power Input
Standard Power	85-264 Vac or 90-300 Vdc
Low Power Option	10-48 Vdc or 12-32 Vac
Power Frequency	DC or 47-63 Hz
Power Isolation	250V rms working, 2.3 kV rms per 1 min test
Power Consumption	2W typical, 3W with max excitation output
Mechanical
Dimensions	129 x 104 x 22.5 mm case
Mounting	35 mm rail per DIN EN 50022
Connectors	Detachable screw-clamp connectors for signal and power RJ45 jack for Ethernet
Environmental
Operating Temperature	0°C to 55°C
Storage Temperature	-40°C to 85°C
Relative Humidity	95% at 40°C, non-condensing
Cooling Required	Mount transmitters with ventilation holes at top and bottom. Leave 6 mm (1/4") between transmitters, or force air with a fan.

Pinout

Datasheet, Manual, Mechanical and Serial I/O info.
Manufacturer site:	https://www.laurels.com/transmitter-dc.php

Laureate 4-20 mA and RS2332/RS485 Transmitter for DC Voltage or Current Input